Tag: garden & home factory

Water Damage Restoration: What In The Note?

July 17, 2018 /

Water damage can cost a lot of money. Learn what you need to observe, to bypass womogliche still more expensive Renovierunngsmassnahmen. The reasons for water damage may be varied, so can be a defective washing machine, a burst pipe, a ruptured aquarium or but flood possible causes for this. Moisture damage can leave serious long term consequences. Ranging from malicious mildew, which induces long-term serious health consequences, to floor and masonry restoration, because the moisture the plaster or for example the laminate (keyword deformation) has damaged.

Such damage is been it needs to eliminate the moisture. This building dryer are usually, in addition to the right heating & ventilation, dehumidifier or larger measures used. To use such a device, several factors are: 1 no excess drying typically it involves composite materials (2 different materials, the) are linked), which should be dried. Because it is min. 2 materials with different properties, can occur quickly to excessive drying.

Possible consequences include cracks in the walls, or deformations in the laminate. In short: too dry to be learned, because here you can do wrong at least as much, like when a water damage! 2. Cavities and floor make a special danger because formation of microorganisms in cavities. So can moisture damage be fixed while on the outside, still have water retention. This go unnoticed, dangerous microorganisms such as mold can be formed for the people. A subsequent mold remediation can very extensively and eat time be, and also cost a lot of money. There is a distinction between 3 different types of drying: room drying insulation layer Rockung screed drying 1 room drying room drying is the most famous and also most widespread kind of drying. This is where using a desiccant dryer or Kondenstrockners reduced the relative humidity in the air. 2. Dammschichtrocknung insulating layer drying is applied usually on uninhabited apartments drying walls. In the humid air from, for example, the partitions is blown by means of high or low pressure process”and further dried in the room with the help of a Kondenstrockners. 3. Drying of screed the screed drying process is similar to the Dammschichtrocknung, this dry air is supplied with pressure in the insulation under the floor. “While the moisture is removed from the material and go back in the room” promoted. Here, the air with condensation or adsorption dryer is, again like in the insulation layer drying, dried. Basically it is advisable to seek the advice of an expert, because this can probably save lots of money. As you have read, as much can be made due to improper drying, wrong, such as when a water damage. Buy matching dehumidifier dehumidifier there are many on the market. To the user not the overview to lose, the page “Dehumidifier Portal.de” made right dehumidifier for every area of application together, to make the selection for consumers. To air dehumidifier Portal.de Andre Kruse

Smeg Home Appliances – Energy Saving Tips

July 6, 2018 /

With new domestic appliances save money and relieve the environment than Smeg want dealer we run stories, how you can save electricity with a timely fridge from Smeg. (Digression: Smeg is an Italian manufacturer of household appliance, which is among others equally famous for Smeg stove) Because Yes, refrigerators and freezers in our kitchen are around the clock in use, it is very worthwhile to pay attention to the power consumption for our wallet. Did you, for example, that in a German household more than a third of the flow of kitchen appliances such as refrigerators, etc. – is consumed? No? In this story, we have gained a large number of valuable information – from the acquisition to the use – of refrigerators that will help you immensely to save money. Where the refrigerator consumes the least electricity? Refrigerators and freezers leave temperature of the environment, to cool off the inside on the appropriate cold. Imagine the best Save refrigerator power? Be sure to put only cold food in the refrigerator. Let thaw frozen food in the fridge from Smeg. The seals on the door of the refrigerator should be flawlessly intact and clean close, so not useless refrigerant escapes.

If a light Frost forms in the Smeg fridge, this is perfectly normal. This Frost is still thicker or formed from a layer of ice, so the power consumption increases in this way also. If a layer of ice has formed, should be in between defrost. Who not want to worry about, can get a device with a so-called “no-frost function”. It saves you the annoying defrosting, cost but a little more energy. The “no-frost function” may be appropriate but, if you must open the fridge door umpteen times and thus increasing moisture in the Smeg fridge, which usually results in the formation of ice. You use the contents of the refrigerator, because an empty fridge uses more energy than a full fridge from Smeg.